Uncoiler-manufacture,factory,supplier from China

1. Hydraulic core expansion with press arm2. Distribution box (frequency conversion control, slow start and slow stop)3. Electric discharging4. Hydraulic 3KW set5.

1. Hydraulic core expansion 2. Electric discharge3. Bearing capacity 8 tons 4. Distribution box (frequency conversion control, slow start and slow stop) 5. Hydraulic 2.2KW setRoll inner diameter: φ508mm; inner diameter expansion and contraction range ф450-500;Maximum outer diameter of material roll: φ1250mm;

Hydraulic core expansion   2. Electric discharge   3. Bearing capacity 10 tons  4. Distribution box (frequency conversion control, slow start and slow stop)  5. Hydraulic 3KW set

Equipment composition: decoiler → forming host → online punching and cutting → splicing table1. Uncoiler: vertical manual tensioning (bearing 3 tons)2.

primary component1. Uncoiler, hydraulic core, distribution container (frequency conversion manage sluggish upward push and sluggish stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. A leveling computing device with eleven leveling rollers (3 top and four lower), with a energy of 5.5KW.3.

main component1. Uncoiler, coil width: 850mm, coil inner diameter: 530mm, maximum coil outer diameter: 1500mm, hydraulic station 3KW set, load-bearing 8 tons2. Leveling and cutting machine, code feeding forward rotation mechanism (forward and reverse screw), 13-roller leveling, 45 on the leveling shaft, 7.5KW motor, hydraulic cutting, pallet punching3. A-section high-speed platform, 2-section high-speed platform, front and back screw width adjustment, feeding speed controlled by frequency conversion4.

main component1. Uncoiler, bearing capacity 2 tons2. Leveling machine3. Roll forming part, main shaft φ40mm, surface hard chromium plating, 6 rows of forming rollers, reinforced ribs, hydraulic punching, 1 set of plane straightening after forming, roll material: GCr15, 1 set of hydraulic system 3.0KW4. One unloading rack5.

1. Uncoiler, hydraulic core expansion, distribution box (frequency conversion control slow rise and slow stop), hydraulic 3KW set, load-bearing 8 tons2. Leveling and cutting machine, 13-roller leveling, hydraulic system 11KW, 2 sets of electric valves, 7.5KW motor, hydraulic cutting, pallet punching3. A-section high-speed platform, 2 high-speed platforms, forward and reverse screw width adjustment, frequency conversion control4. Punch machine, 3 motors, distribution box, mold pneumatic conversion single and double row, oil cylinder heavy engineering oil cylinder5.

main component1. Uncoiler, hydraulic core, distribution box (frequency conversion control slow rise and slow stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. A leveling machine - 11 roller leveling (3 upper and 4 lower), power 5.5KW,3. Integrated punching and shearing machine - code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, hydraulic cutting, manual pin conversion of single and double rows of punching die, typing (trademark), pallet punching4.

main component1. Uncoiler, load-bearing 4 tons, distribution box (frequency conversion control slow stop)2. Leveling machine, 1 roller leveling (3 upper and 4 lower), power 4.0KW3. All-in-one punching and cutting machine, code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, punching die manual pin conversion single and double row, hydraulic cutting, typing (trademark) (optional)4. High-speed platform - high-speed platform, forward and reverse wire width adjustment, frequency conversion control5.

main component1. Uncoiler, hydraulic core expansion, distribution box (frequency conversion control slow rise and slow stop), discharge, load-bearing 5 tons, hydraulic 3KW set2. Leveling machine, 11 roller leveling (3 upper and 4 lower), power 5.5KW,3. Integrated punching and shearing machine, code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, hydraulic cutting, manual pin conversion of single and double rows of punching die, typing (trademark), pallet punching4.

1. Uncoiler, manual core starting, load bearing 4 tons, distribution box (frequency conversion control slow stop)2. Leveling machine, 11 roller leveling (3 upper and 4 lower), power 4.0KW3. Integrated punching and cutting machine - code feeding forward rotation mechanism (forward and reverse screw), hydraulic punching, punching die manual pin conversion single and double row, hydraulic cutting, typing (trademark) (optional)4. High-speed platform - high-speed platform, forward and reverse wire width adjustment, frequency conversion control5.

This cable tray roll forming machine is mainly composed of an uncoiler, a leveling machine, a punching machine, and a roll forming machine. It can produce solid bottom cable trays, tray hole cable trays, ladder cable trays, cable tray covers, etc. We There are professional design engineers who can provide plans and drawings according to needs.Details descriptionThis uncoiler is a hydraulic core expander with an electric unwinding capacity of 10 tons.

main component1 、Uncoiler machine hydraulic loading, passive feeding, load bearing 5 tons, with brake function2、 leveling and punching integrated machine ，leveling up 3 down 4,1 set of hydraulic system, hydraulic cut-off, hydraulic punching3、 roller forming part ，spindle surface plating hard chromium, forming after the plane straight 1 set, roll material: GCr12, lengthened feed guide position4 、Tracking cut ，hydraulic cut (plug), servo tracking, a set of hydraulic system5、 Passive unloading rack 2 sets                      &

The total length of this production line is 42 meters. It can produce metal sheets of 220-1450mm with a thickness of 0.5-3.0mm. It is equipped with two sets of punching dies with large and small gaps. The production speed is 12 meters per minute. The entire assembly line is leveled by an uncoiler. It consists of cutting part-conveying platform-punching machine-conveying platform-roller forming host-receiving frame.The equipment is equipped with a decoiler with a load capacity of 10 tons, hydraulic core expansion, and electric feeding, which is more convenient to operate.

The total length of this cable tray production line is 33 meters. The width of the metal strips used for production is 160~550mm, the thickness is 0.5~1.5mm, and the production speed is 12m/min. The control panel controls the production. It has a high degree of automation, is stable and reliable, and saves costs. , Achieve truly zero laborCable tray forming machine process flowHydraulic uncoiler→Leveling machine→Punching and cutting machine→Conveyor platform→Roll forming part→Unloading rack 

This equipment is a medium-sized cable trough roll forming machine. It is an efficient machine for the production of medium-sized cable trough systems. It is designed for crimping and shaping sheet metal into cable duct sections, providing a reliable and cost-effective solution for cable management. The equipment is equipped with advanced technology and features to ensure precision and quality of the production process. It consists of a roller system that carefully guides sheet metal through a series of rollers, applying pressure to form the desired shape.

The roll forming principal desktop passes the stamped and reduce sheet thru 25 passes of rollers and progressively rolls it into the completed bridge. It consists of a speed-adjustable AC motor, a reducer, a high-precision rolling linear guide, a left and proper transmission box, a transverse adjustment mechanism, and a curler set.

Product nameCable tray roll forming machineRoller materialCR12,hand chrome coatedMaterial thickness0.5-3.0mmMaterial typeGalvanized steelControl systemPLCRoller stations24 stationsMotor power75KWCutting systemHydraulic cuttingHighlight Galvanized steel sheet roll forming machineSchematic diagramfeature:1. Product name: Cable tray roll forming machine2. Motor power:3. Roller material: CR12, hard chrome plated4. Cutting system: hydraulic cutting5. Material thickness: 0.5-3.0mm6. Material type: galvanized steel plate7.

The ladder cable tray has two parts: the side wall and the ladder. We have designed and produced two roll forming machines to produce the two parts of the ladder cable tray respectively, the ladder edge machine and the ladder support machine. You also need a A welding machine welds them together. The width of the ladder frame is the length of the rungs and the length of the ladder frame is the length of the side walls.

Main Component1、 open coil machine ， 300 type open coil, passive feeding, load-bearing 1.5 tons, with brake function2、 leveling, punching, cut off —— hydraulic system 111 KW, hydraulic cut off,3、 High-speed platform ， frequency conversion control, 1 high-speed platform, forward and reverse wire rod width adjustment4、 roller forming part ， spindle φ 60mm, surface plating hard chromium, forming roller 6 rows, roller material: GCr 15, lengthened feed guide position, 1 set of plane calibration after forming5 、unloading rack ， passive unloading rack: 1 branchTechnical Parametersserial numberproject

Serial numbermain componentConfiguration1Uncoiler1. Hydraulic loading rack2. Passive discharging3. Bearing capacity 5 tons4. With braking function 2Leveling and punchingOne machine1. Feeding code positive mechanism (positive and negative lead screw)2. Leveling up 3 down 43. 1 set of hydraulic system4. Hydraulic cutting5. Hydraulic punching3Roll forming part1. The surface of the spindle is hard chromium plated 4. Extended feeding guide2. 1 set of plane straightening after forming3.

main component1、 open coil ，300 type open coil, passive feeding, bearing 1.5 tons, with brake function2、 roller press forming part ， spindle φ 60mm, surface coated with hard chromium, forming roll 14 rows, roll material: Cr 123、 tracking punch, cut off ， hydraulic punch, cut off, hydraulic system 1 set of 5.5+4.0+4.0KW4 、unloading rack ， passive unloading rack 1 branch                                                            Technical Parameter

The perforated cable tray forming machine is a piece of equipment used to make cable trays. Cable tray is a metal frame structure used to support and protect cables. It is often used for cable laying inside buildings.The perforated cable tray forming machine mainly consists of the following parts:Hydraulic decoiler, leveling and cutting integrated machine, punching machine, roll forming host, etc.Technical data:1. Applicable plates:Material-Thickness: 1-3mmRaw materials: galvanized steel and black steel plate2. Working speed: 12 meters/minute3. Molding stations: 25 stations4.